Play the game - move your character around with the arrow keys until you reach the chicken, then press A when it is in the middle of the display. Flip the device over and slide the game cartridge into the bottom, then turn it on. Replace the back covers, insert the battery and put on the battery cover. You now need to add in the 6 wires - just make sure that the light, sound and display connectors all match up (it doesn't matter which of the 3 numbered ports you use for each). Pull out the burnt sound chip from the bottom section and replace it with your new one. Remove the broken red button and put in your new one, then put the bottom circuit board back. Place the sound chip with the red connector on the back of the display. Take out the broken display from the top, and put it your new one. Also take off the top and bottom back panels. Flip it over and take off the battery cover, then remove the battery. Pick up the gaming device and put it in the middle. Read some more pages Everything is Illuminated. Put the cover back on the device and replace the 2 screws. Flip the device over and attach any of the 3 new neon tubes. Change the top left wire and add another wire to now include the new circuit board. Press the power button to see the results.Īdd yet more clue and stick on another new circuit board. Now change the bottom wire so it attaches to the new circuit board, and add a new wire connecting the new board to the other light terminal. Flip the device over and attach both neon tubes, then flip it back over and press the power button.Īdd some glue to the new rectangular area on the device, and stick on your new circuit board. Attach a pink wire to the two pink terminals. Squeeze some glue on to the depressed portion in the top right, then attach the rectangular device with a power button here. Remove the cover and place it on the right. Flip it over and use the screwdriver to remove the 2 screws. Take the large rectangular piece and put it in the middle. ![]() Read some more pages Life Through a Lens. Put the top, front and bottom of the camera back in place. Insert the roll of film next to the mirror. Use the screwdriver to adjust the angle of the mirror so the light path goes through to the viewfinder (see the mirror layout page provided to the right). Remove the broken mirror and insert your new one in its place. Remove the top, front and bottom of the camera and place these pieces on the left. Use the screwdriver to remove 4 screws (1 from the top, 1 from the side, 2 from the front). Pick up the camera and place it in the middle. Flip the whole telephone over and insert the remaining 4 screws into the base. Reattach the yellow cover and the handset. Put the screw back in to hold the new bell in position. Use the screwdriver to remove the screw that is holding in the broken bell, then remove the bell and insert your new one. Now attach both pink wires to the pink terminals with matching symbols. Remove the burnt circuit board and insert your new one. Drag the pink wire up to the left to detach it. Use your screwdriver on the visible screw above the dial, then remove the dial. Now you can take off the handset and the yellow cover, and place both of them over to the right. Flip it over and use the screwdriver to remove all 4 screws. Take the phone and place it in the middle. Read some more pages Statue of Limitations. ![]() Put glue on both the remaining darker sections, then stick on the other arm and the head. Add more glue and stick on the rest of the cape and the right arm (holding the book). Add some more glue, then add the other leg. Squeeze some glue on to the darker curved section, then attach the other leg and cape. Grab the base and place it in the middle. Read some more pages Goodnight, My Darling. ![]() Insert the cassette, then press the eject button again to close it. Flip the cassette recorder back over and press the eject button. Replace the back cover and put the screw back in, then turn it with the screwdriver. Click to remove the panel, then take out the dead batteries and put it new ones. Use the screwdriver on the back panel, and turn it to remove the screw. Now place the cassette recorder in the middle and flip it over. Insert the pencil into the right spool and turn it to get the tape back inside. Grab the cassette tape and place it in the middle. Read some more pages Welcome to Bellariva. Open the clasps on the suitcase, then take everything out and place each object in its highlighted area. Pick up the suitcase and rotate it so you can see the front.
0 Comments
Leave a Reply. |